Build guide

Desk Pod

A desk controller for a leftover AirPod. The AirPod sits stem down in a handle that spins on two bearings and rocks on a magnet in a heavy puck. A Mac app reads its motion: tilt to steer the pointer, spin to scroll, flick to click, flip it over to lock the Mac.

Desk Pod on a desk, the charging case beside the puck

Your kit contains the four printed parts, two bearings and a magnet pair, and a link to download the Mac app. No AirPod comes with it: you bring your own, the model and ear you picked at checkout. It pops back out intact and charges in its own case. No tools, screws or glue.

At a glance

Printed parts
4
Difficulty
Beginner
Build time
about 15 min

Parts checklist

Printed parts

Navy

Light blue

The printed parts next to an open charging case

Hardware

No screws or glue: the bearings and magnets press in.

What you bring

Assembly

Exploded view of Desk Pod
From the top: cap, AirPod, handle, bearings, foot with spindle, puck.
  1. 1Bearings into the handle

    • Press the first 6700ZZ bearing straight up into the seat at the bottom of the handle until it stops.
    • Press the second one in under it, until it sits flush.
    Check Both bearings are square in the seat and spin freely with a finger.
  2. 2Magnets into the foot and the puck

    • Let the two magnets snap together and mark the top of the stack with a pen.
    • Pull them apart without turning either one over.
    • Press the top magnet into the bottom of the foot, marked face first.
    • Press the other magnet up into the pocket under the puck, the face that touched the first magnet going in first. The ribs hold it.
    Check Set the foot in the puck's socket: it pulls down flat and centres itself. If it pushes away, one magnet is upside down: press it out and turn it over.
  3. 3Handle onto the spindle

    Handle onto the spindle
    • Slide the handle's bearings down over the foot's spindle until the handle stops on the shoulder.
    Check The handle spins freely on the foot.
  4. 4Into the puck

    Into the puck
    • Set the foot into the socket on top of the puck.
    • Tilt the handle in any direction and let go.
    Check It rocks to the socket wall and the magnets pull it back upright.
  5. 5AirPod and cap

    AirPod and cap
    • On your Mac, open System Settings › Bluetooth, click ⓘ next to your AirPods and turn off Automatic Ear Detection.
    • Put the AirPod stem down into the handle. It only fits one way.
    • Press the cap on, turning it until its key drops into the handle.
    Check The AirPod sits firmly with the cap closed. To charge it, take the cap off and put the AirPod back in its case.

Set up the Mac app

After you order, you get an email with a link to download the Desk Pod app. It needs macOS 14 or later and your AirPods connected to the Mac.

  1. Open Desk Pod.app. It starts paused.
  2. The first time, it walks you through four steps. Each one saves by itself with a short sound, so you never have to press a button while holding the handle:
    • Connect: the AirPod is in the handle; the step passes once motion arrives.
    • Spin: spin the handle in the puck for about two seconds.
    • Let go: hands off. Its resting position becomes the centre.
    • Tilt right: groove facing you, push the handle to the right and hold it for a second.
  3. Press Allow Mac control and turn Desk Pod on under System Settings › Privacy & Security › Accessibility. Back in the app, press Start.
The Desk Pod Mac app
The app shows the handle from above, with each motion's job where it happens.

Using it

  • Pointer mode: tilt to move the pointer and come back to the centre to stop. Spin to scroll. Flick the handle into a fast spin to click where the pointer is.
  • Shortcuts mode: hold a tilt past the ring to run its shortcut. Spin to switch between your open apps. Under Assign shortcuts… each tilt and the flick can run a key combination, a named Apple Shortcut, or next and previous app.
  • Flip it over to lock the Mac, in either mode.
  • Escape, Pause or the menu-bar item stops it at any time. The gear opens the settings: pointer speed, rest zone, reverse directions, and Set up again….
Tip If the pointer drifts, use Re-home (⌃⌥⌘H) with the groove facing you, or run Set up again….